Lumenier LUX V2 Flight Controller

クリックで画像を表示
クリックで画像を表示
クリックで画像を表示


Lumenier LUX V2 Flight Controller


Lumenier LUX V2フライトコントローラーには、MPU6000やUARTポートが５つ、SDカードスロットなど新機能が追加されてた新しいコントローラーです。
最新のBetaFlightファームウェアでDSHOTプロトコルもサポートしています。





Hardware Features

New in V2
Dedicated UART for RC RX use, no need to solder a jumper to select PPM/SRX anymore.
Dedicated telemetry UART, this brings the total to 5x plus USB.
SD Card slot for BlackBox data recording (SD card not included)
Low noise MPU6000 SPI Gyro.
USB detection can disable things like buzzer when configuring on the bench.
New ultra low noise regulators for MCU and IMU power systems.
USB Conflict resolution - Hardware inversion, SBUS or telemetry can be used on any of the 3 available hardware serial ports. USB will not interfere with peripherals.
High Speed SPI 8kHz Gyro
MPU interrupt connected to F3, allowing the F3 to know immediately when fresh data is available.
Dedicated Boot button for easy firmware flashing.
Reinforced solder pads for trouble-free direct soldering.
Extremely low profile design.
Recessed, sideways pin headers. Also enables soldering of all wires directly to pads without use of any pin headers.
Integrated FRSky RSSI Filter (RC filter).
Input voltage 6v to 24v. Power the board directly from flight pack up to 6S (on 'BAT' pad only!).
VIN + VBAT merged - A single wire to power the board will provide voltage input and Telemetry/OSD voltage data.
Filtered voltage output - output 5v 1A (and 3.3v where applicable) to power peripherals such as GPS, RX, BLACKBOX, OSD. 5v/3.3v RX selectable.
Note: RX pad is dedicated to UART 4 in the Configurator.
Software/Hardware Features

Betaflight support (Supports new DSHOT protocol)
Cleanflight support (RACE target).
BLHeli passthrough flashing supported by hardware 
Raceflight ready
Specifications

STM32F303RCT6(256kB flash) 32-bit processor
MPU6000 SPI Gyro/Accelerometer
Micro SD memory card slot (SD card not included)
High quality, gold plated PCB
Highest quality components, individually sourced to meet Lumenier standards
Micro USB connector for programming
Dimensions: 36x36x6mm (includes USB in height)
Mounting Holes: 30.5mm square to center of holes 
Weight: 5g


Includes

1x Lumenier Lux V2 Flight Controller
2x 2x7 Straight Pin Headers


Downloads

Download the Lumenier LUX V2 User Manual (coming soon)
Download Betaflight Configurator - Latest Betaflight Firmware  (Load the "LUXV2_Race" target)
Download Raceflight (Target coming soon)

FC65412

この商品を買った人はこんな商品も買っています

この商品をチェックした人はこんな商品もチェックしています

ログイン・会員登録

いらっしゃいませ ゲスト 様

会員ＩＤ：

パスワード：

[パスワードの再発送]

Category

My Cart

カートに商品は入っていません

新着商品

商品検索


カテゴリー内を検索

お問い合わせフォーム

お問い合わせ

paypal

QAV


HQ-Prop


Skyzone